MF-DM500WBSW BEAM SHARPY MOVING HEAD LED STAGE LIGHT
Specifications:
OPERATING MODE
| DMX Control | DMX mode, receive DMX signal, RDM signal |
| Auto Run | Fixture run automatically according to built-in programs |
| Sound Control | When the fixture detects a strong sound, the fixture automatically runs a scene according to the built-in program, otherwise it will stay the last scene |
| Scene Mode 01 | runs in a set scebe, which supports most of the custom editing of 10 scenes. |
| 1~10 | outputs the specified scene |
| Auto | Automatically loops the output scene in the set scene time (non-zero) order, and the scene with time 0 automatically ignore |
| M/S Choose | Master and slave selection, non-DMX mode takes effect, select the mode of data output, fixture detect DMX cable state automatic switch output, prevent data conflicts |
| Master | Fixture runs built-in program. If DMX has no signal, it outputs data (synchronization), otherwise it does not output data. |
| Slave | Fixture runs built-in program and do not output data |
| Auto | If DMX has no signal, the fxiture will runs built-in program. Otherwise, the fixture will run in DMX Mode(follow DMX). |
| Lamp Switch | (Lamp light source) pop-up confirmation dialog box, select "SURE" to confirm the current operation, turn on or off the lamp, switch time interval limited to 30 seconds |
| Off | The current lamp output is off |
| On | The current lamp output is turned on |
DISPLAY SETTING
| Language | Display language settings |
| English | English display |
| Chinese | Chinese display |
| Screen Saver | Set screen 30 seconds without operation, the screen's display content or method. |
| OFF | Keep the last operation page |
| Mode1 | Black |
| Mode2 | Black screen, showing the address code of the current fixture in the lower left corner. |
| Mode3 | Display trademark information, address code and operation mode. |
| Screen Rot | Set the display direction of the screen. |
| OFF | No reverse display |
| ON | Reverse display |
| DMX Indicate | Set the indication mode of DMX signal indicator. |
| Mode1 | When signal is bright, no signal is off. |
| Mode2 | When signal is off, no signal is bright. |
| Mode3 | When signal is flash, no signal is off. |
| Screen Light | Set the screen backlight for 10 seconds without operation |
| 1~10 | 10 |
Common Fault:
According to some common faults, the corresponding solutions are put forward.Any unsolvable problems should be dealt with by professionals.Disconnect the light fixture before maintaining it.
1. Light bulb is not on
Check that the voltage that matches the light fixture is installed;
Check whether the lamp supply power connection or control switch is in bad contact;
Check if the power supply is insufficient;
Check that the DMX512 controller is sending instructions.
2. The light fixture does not accept control from the console after normal reset
Check luminaire digital start address value and function options are correct;
Check whether the connection of communication control line is correct, the communication line is too long or has been interrupted;
Check whether the control equipment is invalid, check whether the serial access signal amplifier is invalid;
Check whether the communication line is too long or other equipment interferes with each other;
Optimize wiring, shorten the length of control signal lines, high voltage and low voltage lines separate wiring Add signal amplifiers;
Signal line using high-quality shielded twisted pair wire;
Connect the signal terminal resistor (120 ohm) at the end of the lamp.
3. Luminaire does not start
Check that the power supply parameters are consistent with the lamp;
Check the poor contact caused by extrusion deformation, vibration and moisture of internal parts in the long distance transportation process or fall off. Please check whether the internal wire integration connector of the lamp has fallen off or loosened.
Check whether the electronic components of the lamp (such as electronic transformer, PCB board, motor control board, etc.) are loose, short circuit and burned out.
4. When working, the action of the X or Y axis of the lamp is not normal
Follow the previous step to check them one by one;
Check whether the transmission belt corresponding to the X and Y axis directions in the lamp falls off and breaks;
Check whether the data feedback receiver (optocoupler)
corresponding to the X and Y directions in the lamp is damaged;
Restart the machine and reset it once.
Panel Operation:
BRIEF
The light panel diagram show as Figure 3, above area is fixture description, below area show fixture real-time status, such as DMX cable status, lamp status, error or information(ps. when there are message hav't been checked, echo 'ERR' in status bar, otherwise echo 'NOR'). Display & operation just like 'Android operation system', when select or set item value, system save the settting immediately. RDM protocol is embed in fixture, user set DMX address via cable using the controller surpport RDM function. when fixture was search by controller, displayer will echo 'RDM' indicate this RDM is work.
OPERATION
Operate fixture with touch or encoder/button
The left area is TFT Displayer and touch(product which support touch), chick item or value with finger will to complete operation of set light setting(parameters) or view light state.
The area on the right hand side is rotary encoder with button or key, As auxiliary input interface, if fixture disable touch function, the encoder/key can been choose to set or view the item, and then press the encoder button/key to confirm the selection, rotary
encoder or push key again set the parameter value, finally, Press encoder button/key one again to save value or setting. Parameter value setting When the selected item is value need to been modified, the dialog shown in Figure 4 will pop up.
Modify value:Can quickly modify value via pull the slider to the desired position, or click the button of 'up' or 'down' whit finger on the right side to set the exact desired value, another way is roll encoder on the right hand side of panel.
Apply value:When Value had been modified, Then press the bottom of 'apply' in the left corner to apply to the light, but haven't saved;
Save Value:Any time, click on the lower right corner of the "OK" button, the setting will been saved into internal memory.
Boolean parameter setting
when the selected parameters is a Boolean value (such as ON or OFF), can directly modify setting by chick corresponding item, the setting will been saved right now. When the parameter is a key item, chick corresponding item, a dialog shown in Figure 5 will been popup ask for the confirm. Chick 'sure' to confirm.
Sub Menu(Parameter)
Installation:
CABLE CONNECTION DMX
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24AWG, low capacity. Do not use microphone cable or other cable withcharacteristics differing from those specified. Theendconnections must be made using XLR type3 or 5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4W)between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.
RIGGING(OPTIONAL)
This equipment can be positioned and fixed by clamp in every direction of the stage. Locking system makes it easy to fasten to the bracket.
Attention! Two clamps is needed to fix the equipment. Every clamp is locked by fastener of 1/4 kind. Fastener can only be locked clockwise.
Attention! Fasten a safety string to the additional hole of side aluminum piece. The secondary accessory can not hang on the delivery handle. Nip the equipment on bracket.
Check if rigging clamp (not including the one inside) damaged or not? If stand ten times weight as the equipment. Make sure the architecture can stand ten times weight as all the equipments, clamps, wirings and other additional fixtures.
Screws for clamping must be fixed firmly. Take one M12 screw (Grade 8.8 or higher) to clamp bracket, and then screw the nuts.
Level the two hanging points at the bottom of clamp. Insert fastener to the bottom, lock the two levers by 1/4 rotating clockwise; then install another clamp.
Install on safety string which stands at least ten times weight as equipment. Terminal of the accessory is designed for clamps.
Make sure pan/tilt lock unlocked or not. Keep the distance more than 1M from equipment to flammable material or lighting source.
Applications:
Moving head lights are versatile lighting fixtures used in stage productions, concerts, nightclubs, and other entertainment events. They consist of motorized heads that can move horizontally and vertically to direct light beams. They are used to illuminate performers, create dynamic lighting effects, and enhance visual displays.
Packing:
| Product Name | Quantity |
| | 1 PCS |
| Power-line | 1 BASE |
| User Manual | 1 PCS |
FAQ:
Q1: What do you sell?
A1: We provide good quality of floodlight, high bay light, explosion proof light, tri-proof light, downlight, and other lighting products, as well as responsible services and reliable after-sales warranty.
Q2: Is it OK to print my logo on led light product?
A2: Yes. We provide ODM and OEM services. Please inform us formally before our production and confirm the design firstly based on our sample.
Q3: How to deal with the faulty?
A3: During the guarantee period, we will send new lights with new order for small quantity. For defective batch products, we will repair them and resend them to you or we can discuss the solution including re-call according to real situation.
Q4: Can I have a sample order for led light?
A4: Yes, we welcome sample order to test and check quality. One sample or mixed samples are acceptable.
Q5: How long time to ship the goods if place an order?
A5: Usually 7 days for sample or small order,15 working days for bulk order, but sometimes depend on the order quantity.
Product Tags:
|
|
IP20 Wedding Light 22 27 CH Nightclub Party Event Equipment 500W LED Moving Head Spot Light Images
|
